****HOW BOOST BOTTLES WORK ****
As the engine (any engine) draws fuel and air in through the carb on the intake cycle, the spark plug fires this mixture forcing the piston down and sucks a small amount of air into the carburetor for the next intake cycle. As the piston and crank bottom’s out on the bottom of the cylinder, the piston begins to make its return upward. As this cycle is happening, the piston pushes air back through the carburetor naturally under pressure. This action creates a reverb effect and causes the air / fuel mix to become double rich as by now it is processed TWICE by your carbs fuel jets. Most commonly, this results in rough idle, hesitation, bogging, and the ever-so- frustrating: Sputtering at top end. The reason the sputtering and bogging is happening is because of the double rich mixture. Heavy exhaust smoke, heavy engine loading is often looked at as too much oil / fuel ratio, bad carburetor, etc. While this may be one of those problems, it often is not. Your engine is actually choking itself out with a bad fuel mix! The installation of our Boost Induction Systems™ Boost bottles eliminates this nagging problem. (Hence the location of the inlet) Our Patent Pending Internal Metering System™ Automatically adjusts itself to work with your engines compression and carburetor. Our bottles will eliminate the reverb caused by your pistons return to top dead center (TDC) and remove the double mix! Now, with the bottle installed, operators are now no longer fooled by the double rich mix. This now allows proper adjustability of the carburetor! Tired of sacrificing top end speed for low end? Or low end speed for high? That’s because you have a double rich mix.You cannot have one or the other without a proper intake booster (Boost bottle).
WHAT ARE THE ADVANTAGES OF A "DUAL" BOTTLE KIT? WHY ARE 2 BOTTLES BETTER THAN ONE?
This is a great question. Having 2 inlets on the manifold doubles the passageway for both the rising pressure of the cylinder, and the other inlet for the downward. They will both work together to smooth out the incoming airflow and add a substantial amount of power rather than just one bottle alone. While a single bottle kit is VERY effective, the Double bottle kits are demanded by the more savvy engine builders, and competition racers whom have upgraded their engines and are going for the "Elite" in horsepower, torque and RPM gains rather than just a recreational hobby enthusiast.
WHAT IS IN THE BOOST BOTTLE AND DO I NEED TO REFILL IT?
No, you do not need to refill the boost bottle as their sole purpose is to even out your fuel mix and apply the right amount of pressure to let you carburetor breathe better. Once your boost bottle is mounted on your engine, please do not remove it. It will outlast the life of your engine and can be transfered from one engine to another for years to come. It does not need to be refilled.
HOW DO KNOW IF IT WILL FIT MY ENGINE?
IF YOUR ENGINE IS ONE OF THE FOLLOWING: / G230RC / G260RC / G260PU / G260PUH / G231PUH / G231PUM / G260PUM engines. If your model is not mentioned, most likely, your engine has this manifold. Take a good look at it and match for comparison. Email us if you are not sure!
Chung Yang CY23RC / CY26RC / CY27RC / CY29RC / GP290 engines. Works with Walbro WA / WT series carburetors.
For R/C:: Fits a wide variety of 1:5 and 1:6 R/C cars, planes, boats, and helicopters. Same mounting dimensions as Zenoah G230RC / G260RC. For cars - fits FG: Marder, Leopard, Monster Beetle, Monster Truck, Stadium Truck, Pajero, Sportsline, etc. Also fits Duratrax Firehammer, Firehammer MT, XTM Grizzly, Carson Attack, HPI Baja 5b, Traxxas Monster Buggy, MCD Rally, MCD Race Runner, MCD 4x4 Monster Truck, and most other large scale onroad and offroad RC cars.
I AM CONFUSED, HOW AM I GOING TO INSTALL THIS ON MY ENGINE, AND WHERE DOES IT HOOK UP?
Our kits come with a pre-tapped manifold that is "BOLT ON GUARANTEED" These boost bottles are attached to the manifold. In this auction a manifold is included to help ease installation. Installation time is about 20 mins. The manifold or (Carb block) is the metal or plastic piece that separates your carb from your cylinder. In this application, we have included a pre-tapped OEM manifold. We work closely with Zenoah, Chung Yang, and many manufacturing companys directly to carry a top notch product.. We specialize in competitive prices, outstanding customer service, and research and design.
*THIS IS AN AFTERMARKET RACING PRODUCT DESIGNED TO INCREASE TO SPEED SAFETY RATING SET BY THE MANUFACTURER AND SHOULD BE USED BY EXPERIENCED OPERATORS UNDER CLOSED COURSE CONDITIONS / SUPERVISION. HIGH PERFORMANCE UPGRADES SUCH AS THIS BOOST BOTTLE KIT CAN MAKE VEHICLES UNSTABLE / UNSAFE AT HIGH SPEEDS. PLEASE REMEMBER TO ALWAYS RESPECT AFTERMARKET UPGRADES AND USE GOOD JUDGEMENT.
COPYRIGHT© 2011 BOOST INDUCTION SYSTEMS - U.S.A ALL RIGHTS RESERVED